Description Description 6in x 39in - .060, Surface mounted anodized aluminum kick plate (152.4mm x 990.6mm) Use construction adhesive for standard installation. Available pre-drilled or pre-drilled and countersunk for use with mechanical fasteners. Custom sizes are available. Product Features Materials: Anodized Aluminum: Type 5052, .060 gauge, with a #4 satin finish. Adhesive: Polyurethane based construction adhesive Fabrication: Kick Plates shall be factory formed from anodized aluminum sheet. Edge burrs shall be removed Satin finish grain oriented parallel with length. Optional beveled edge will have a 45° chamfer on 1 to 3 sides, dimension .030 EXAMINATION Verification of conditions: Examine areas and conditions under which work is to be performed and identify conditions detrimental to proper or timely completion. Do not proceed until unsatisfactory conditions have been corrected. PREPARATION Surface preparation: Prior to installation, clean substrate to remove dirt, debris and loose particles. Perform additional preparation procedures as required by manufacturer’s instructions. Protection: Take all necessary steps to prevent damage to material during installation as required in manufacturer’s installation instructions. INSTALLATION Install the work of this section in strict accordance with the manufacturer’s recommendations, using only approved mounting hardware, and locating all components firmly into position, level and plumb. CLEANING General: Immediately upon completion of installation, clean material in accordance with manufacturer’s recommended cleaning method. Remove surplus materials, rubbish and debris resulting from installation as work progresses and upon completion of work. Protection Protect installed materials to prevent damage by other trades. Use materials that may be easily removed without leaving residue or permanent stains. Documentation Drawing (712k) Suggested Specifications.pdf (243k) KickPlate Installation.pdf (68k) Kickplate Care & Cleaning.pdf (69k) TheKickPlateStore Warranty.pdf (69k) Optional Standard Hole Pattern Number of Holes: 8: 4 on Top, 4 on the Bottom Description 6in x 39in - .060, Surface mounted anodized aluminum kick plate (152.4mm x 990.6mm) Use construction adhesive for standard installation. Available pre-drilled or pre-drilled and countersunk for use with mechanical fasteners. Custom sizes are available. Product Features Materials: Anodized Aluminum: Type 5052, .060 gauge, with a #4 satin finish. Adhesive: Polyurethane based construction adhesive Fabrication: Kick Plates shall be factory formed from anodized aluminum sheet. Edge burrs shall be removed Satin finish grain oriented parallel with length. Optional beveled edge will have a 45° chamfer on 1 to 3 sides, dimension .030 EXAMINATION Verification of conditions: Examine areas and conditions under which work is to be performed and identify conditions detrimental to proper or timely completion. Do not proceed until unsatisfactory conditions have been corrected. PREPARATION Surface preparation: Prior to installation, clean substrate to remove dirt, debris and loose particles. Perform additional preparation procedures as required by manufacturer’s instructions. Protection: Take all necessary steps to prevent damage to material during installation as required in manufacturer’s installation instructions. INSTALLATION Install the work of this section in strict accordance with the manufacturer’s recommendations, using only approved mounting hardware, and locating all components firmly into position, level and plumb. CLEANING General: Immediately upon completion of installation, clean material in accordance with manufacturer’s recommended cleaning method. Remove surplus materials, rubbish and debris resulting from installation as work progresses and upon completion of work. Protection Protect installed materials to prevent damage by other trades. Use materials that may be easily removed without leaving residue or permanent stains. Documentation Drawing (712k) Suggested Specifications.pdf (243k) KickPlate Installation.pdf (68k) Kickplate Care & Cleaning.pdf (69k) TheKickPlateStore Warranty.pdf (69k) Optional Standard Hole Pattern Number of Holes: 8: 4 on Top, 4 on the Bottom
Choose Options Add To Quote TheKickPlateStore 6in x 23in - .060, Anodized Satin Finish, Aluminum Mop Plates MP-AN-060623-SA MSRP: Was: Now: $23.70 - $43.70
Choose Options Add To Quote TheKickPlateStore 6in x 34in - .060, Anodized Satin Finish, Aluminum Mop Plates MP-AN-060634-SA MSRP: Was: Now: $28.60 - $48.60
Choose Options Add To Quote TheKickPlateStore 6in x 44in - .060, Anodized Satin Finish, Aluminum Mop Plates MP-AN-060644-SA MSRP: Was: Now: $33.10 - $53.10
Choose Options Add To Quote TheKickPlateStore 8in x 39in - .060, Anodized Satin Finish, Aluminum Mop Plates MP-AN-060839-SA MSRP: Was: Now: $36.60 - $56.60
Choose Options Add To Quote TheKickPlateStore 6in x 39in - .080, Anodized Satin Finish, Aluminum Mop Plates MP-AN-080639-SA MSRP: Was: Now: $35.00 - $55.00