Categories

Brands

Our Other Sites

8in x 34in - .060, Anodized Satin Finish, Aluminum Mop Plates

See more by TheKickPlateStore

$33.60
8in x 34in - .060, 5005, Anodized Satin Finish, Aluminum Mop Plates - On Door
Hover Image to Zoom

8in x 34in - .060, Anodized Satin Finish, Aluminum Mop Plates

See more by TheKickPlateStore

$33.60
SKU:
MP-AN-060834-SA
Availability:
Ship Time of 6-8 Business Days
Weight:
4.00 LBS
Width:
34.00 (in)
Height:
8.00 (in)
Depth:
0.06 (in)
Shipping:
Calculated at Checkout
Bulk Pricing:
Buy in bulk and save

Bulk discount rates

Below are the available bulk discount rates for each individual item when you purchase a certain amount

  • Buy 20 or above and get 10% off
See Full Details

Std Lead Time: Approx 6-8 bus. days until shipment | Large QTY Lead Time: Approx 8-12 bus. days until shipment | Options may increase lead time | If you need something sooner, please check the Category: Ships Today or call 800-516-4036

Adding to cart… The item has been added
Add to Wishlist

Description

8in x 34in - .060, Surface mounted anodized aluminum kick plate (203.2mm x 863.6mm)

Use construction adhesive for standard installation. Available pre-drilled or pre-drilled and countersunk for use with mechanical fasteners. Custom sizes are available.

Product Features

Materials:

  • Anodized Aluminum: Type 5052, .060 gauge, with a #4 satin finish.
  • Adhesive: Polyurethane based construction adhesive

Fabrication:

  • Kick Plates shall be factory formed from anodized aluminum sheet.
  • Edge burrs shall be removed
  • Satin finish grain oriented parallel with length.
  • Optional beveled edge will have a 45° chamfer on 1 to 3 sides, dimension .030

Examination

Verification of conditions: Examine areas and conditions under which work is to be performed and identify conditions detrimental to proper or timely completion. Do not proceed until unsatisfactory conditions have been corrected.

Preparation

  • Surface preparation: Prior to installation, clean substrate to remove dirt, debris and loose particles. Perform additional preparation procedures as required by manufacturer’s instructions.
  • Protection: Take all necessary steps to prevent damage to material during installation as required in manufacturer’s installation instructions.

Installation

  • Install the work of this section in strict accordance with the manufacturer’s recommendations, using only approved mounting hardware, and locating all components firmly into position, level and plumb.

Cleaning

  • General: Immediately upon completion of installation, clean material in accoardance with manufacturer’s recommended cleaning method.
  • Remove surplus materials, rubbish and debris resulting from installation as work progresses and upon completion of work.

Protection

Protect installed materials to prevent damage by other trades. Use materials that may be easily removed without leaving residue or permanent stains.

Documentation

Optional Standard Hole Pattern

Number of Holes: 6: 3 on Top, 3 on the Bottom

Hole

  • Description

    8in x 34in - .060, Surface mounted anodized aluminum kick plate (203.2mm x 863.6mm)

    Use construction adhesive for standard installation. Available pre-drilled or pre-drilled and countersunk for use with mechanical fasteners. Custom sizes are available.

    Product Features

    Materials:

    • Anodized Aluminum: Type 5052, .060 gauge, with a #4 satin finish.
    • Adhesive: Polyurethane based construction adhesive

    Fabrication:

    • Kick Plates shall be factory formed from anodized aluminum sheet.
    • Edge burrs shall be removed
    • Satin finish grain oriented parallel with length.
    • Optional beveled edge will have a 45° chamfer on 1 to 3 sides, dimension .030

    Examination

    Verification of conditions: Examine areas and conditions under which work is to be performed and identify conditions detrimental to proper or timely completion. Do not proceed until unsatisfactory conditions have been corrected.

    Preparation

    • Surface preparation: Prior to installation, clean substrate to remove dirt, debris and loose particles. Perform additional preparation procedures as required by manufacturer’s instructions.
    • Protection: Take all necessary steps to prevent damage to material during installation as required in manufacturer’s installation instructions.

    Installation

    • Install the work of this section in strict accordance with the manufacturer’s recommendations, using only approved mounting hardware, and locating all components firmly into position, level and plumb.

    Cleaning

    • General: Immediately upon completion of installation, clean material in accoardance with manufacturer’s recommended cleaning method.
    • Remove surplus materials, rubbish and debris resulting from installation as work progresses and upon completion of work.

    Protection

    Protect installed materials to prevent damage by other trades. Use materials that may be easily removed without leaving residue or permanent stains.

    Documentation

    Optional Standard Hole Pattern

    Number of Holes: 6: 3 on Top, 3 on the Bottom

    Hole

Related Products

Customers Also Viewed

!